RASID Hardware Units
Below are the RASID Hardware Units
| SIM card requirements | Provide GPRS/3G data sim card with a minimum data capacity of 20 Mb for a month. |
| GSM(GPRS) | Quad Band 900/1800 MHz, 850/1900 MHz GPRS Class 10 (Upto 85.6) SMS for OTA configuration |
| GPS/GPS+GLONASS | NMEA-0183 Protocol 32 channel receiver High sensitivity, not less than -161 dBm |
| IMEI | Device IMEI should be valid under TRA |
| Latitude & Longitude Format | Device should send the latitude and longitude in decimal format |
| Date & Time Format | Device should sent the date and time in UTC format |
| Speed Format | Device should send the speed in miles/hour format |
| Direction Format | Device direction setting should have 0-360 degrees |
| Digital Inputs | Minimum 2 digital inputs |
| Digital Outputs | Minimum 2 digital outputs |
| Analog Inputs | Minimum 1 analog input |
| 1 Wire Interface | Device Should have 1 wire interface for temperature/ibutton |
| Power supply | The power supply should be between +5 to +30 v |
| USB/Serial interface | The USB/Serial interface should be available for initial configuration |
| Internal battery | The internal battery should have a minimum backup of 24 hours |
| FOTA/ USB/ Serial | The firmware of the device should be upgradable through OTA as well as USB/Serial interface |
| Flash Memory | Flash memory should be minimum 2 MB ( or equivalent to >= 2000 offline records) for saving the records, when GSM not available |
| Data-sending mode | Device should send the data in time, distance and direction mode |
| PTO Connection | To get the PTO status |
| CAN Interface | Mandatory for the vehicles that have CANBUS for accurate data |
On-Board Weighing System for Bulk Collection
| Communication | RS232 Communication (Serial Communication) |
| Weight data | Total weight Weight per location Partial weight (weight on collection) |
| Alerts Configuration | Configuring weight limit Alert for overloading |
| Data pushing mode | Data pushing on event (bin collection) Data pushing on predefined Interval |
| Data polling mode | Data Polling on Request(online Polling) |
| Weight Sensors | To get the weight of the bins based on location |
| Accuracy | 1% full scale |
| Capacity (GVW) | 17 -50 Tons |
| Operating Voltage | 15 -30V |
| Operating temperature | 0 to 60 degree C |
| Inclinometer – chassis lean alarm | 3 degrees |
| Inclinometer – body load alarm | 40% off centre |
| Weighing modes | Standard, axle, twin/5th wheel and air, drawbar |
| Indicator type | LCD |
| Indicator size | 79.0 x 30.9 mm |
| Indicator operating temperature | -10 to + 50 °C |
| Indicator environmental protection | IP20 |
| Indicator resolution 240 x 90 Dots | 240 X 90 dots |
| Dot pitch | 0.42 mm |
| Load cell port | 4 pin connector (for junction box) |
| Overload alarm – audible | Optional external alarm sounder on vehicle |
| Password protection | 4 digits, manager and user PIN |
| Form factor | Din cut out |
| Load cell types | Up to 8 CANbus or analogue load cells |
| Interfaces | RS232 |
| Baud rate | 1200, 2400, 9600, 19200, 57600 |
| Connector | 9 pin to printers/scoreboard bps |
| Printer capability | Impact or heavy duty type |
| Wireless Remote Handheld Unit | Range Up to 50 meters in open terrain 15 channels , A-O, Frequency 868MHz (complies with the European license free ISM band regulations) Viewing area 50.6 x 31.0 mm Minimum voltage 3.3 (with reminder on screen) Vdc Max charging voltage 4.2 V dc Charging time Three hours approximately, discharged to full, Battery type -Nickel Metal Hydride, rechargeable – ruggedized, Backlight 8 seconds per button push, IP 66 Protection |
| RFID Interface | For the personnel identification |
| Two-way communication | With the driver |
| Features and alerts within the device | |
| Ignition On/Off | Ignition On/Off status alert |
| Engine Immobilization | Engine Immobilization (as output) |
| Overspeed | Overspeed alerts |
| SOS button (optional) | SOS alert during emergency – Panic Button |
| Harsh braking | Harsh braking alert during rash reduction in velocity |
| Harsh cornering | Harsh cornering alert during rash change in angular velocity |
| Harsh Acceleration | Harsh acceleration alert during rash change in velocity |
| Temperature Sensor (optional) | Environment temperature |
| Fuel Sensor (optional) | Fuel sensor for the detection of fuel level of the device |
| Device battery Low | Battery Low status of internal and external battery |
| Towing | Tow alert during illegal movement of the vehicle |
| Tampering/Battery Removed | Tampering/Battery Removed alert when primary power supply is cut off |
| Geo-fence | Geo-fence feature should be available within the device |
| Weight | The weight of the collected waste based on the location |
The container level sensor should be designed and built to accurately measure container fill levels in harsh environmental conditions. It should employ ultrasonic sonar technology together with temperature and motion sensors. The smart software should be able to measure the fill level and automatically detect important events such as container collections, fire and vandalism. Advanced algorithms to be applied to determine the fill level even if the surface of the contents is unevenly shaped. Measurements to be performed at confgurable intervals, usually once per hour.
- Reader
- Reads any Maxim iButton through 1-wire (onewire) interface
- All metall parts are chromium-plated
- Should be compatible with any access control device
- Plastic casing
- M12 thread
- Standard wire – 40 cm
- Waterproof
- ID
- Waterproof iButton probe without LED
- Reads any Maxim iButton through 1-wire (OneWire) interface
- Should be compatible with any access control device
- Standard wire – 40 cm
- Made from high grade stainless steel: 1.4418
- Full resistance to halogen elements (e.g. sea water)
- Should be compatible with UTAH-P (magnetic) holders
